Garmin GMM 150 Marine Monitor Manual de instalación descargar pdf (Pagina 2)

The smaller

in. (3.5 mm) hole

on the nut plate should

line up with the smaller hole on the template.

If the smaller

in. (3.5 mm) hole on the nut plate does not

line up with the smaller hole on the template, mark the new

location.

Repeat steps 10–11 for each of the nut plates along the

sides of the device as indicated on the template.

Using a

in. (3.5 mm) drill bit, drill the smaller holes.

Remove the template from the mounting surface.

Starting in one corner of the mounting location, place a nut

plate

on the back of the mounting surface, lining up the

large and small holes.

The raised portion of the nut plate should fit into the larger

hole.

Secure the nut plate to the mounting surface by fastening an

included M3 screw

through the smaller

in. (3.5 mm)

hole.

Repeat steps 15–16 for each of the nut plates along the

sides of the device.

Install the rubber gasket

on the back of the device.

The pieces of the rubber gasket have adhesive on the back.

Make sure you remove the protective liner before installing

them on the device.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

NOTE: To prevent corrosion of the metal contacts, cover

unused connectors with the attached weather caps.

Place the device into the cutout.

Secure the device to the mounting surface using the included

M4 screws

Install the decorative bezel by snapping it in place around the

edges of the device.

Connection Considerations

NOTICE

A blue rubber seal is included for each DVI port on the device.

This seal must be installed between each DVI port and DVI-

cable connector to avoid damage to the connectors.

When connecting the GMM device to power and to a GPSMAP

8500 device, observe these considerations.

• Although it is recommended to use the Garmin provided DVI

cables, high-quality third-party DVI cables may be used.

Before a DVI cable is routed, it should be tested by

connecting the devices with it.

• The GMM device should be connected to the same power

source as a connected GPSMAP 8500 device. If this is not

possible, the devices must be connected to the same

ground.

• The power and ground connections to the battery must be

checked to make sure they are secured and will not become

loose.

• The touchscreen functionality of the GMM device can be

used to control one GPSMAP 8500 device.

• The GMM device used to control a GPSMAP 8500 device

must be connected to both the GARMIN PROCESSOR BOX

and MAIN DVI VIDEO IN ports on the GMM and the

GARMIN MONITOR and MAIN DVI-I VIDEO ports on the

GPSMAP 8500 using a Garmin Marine Network cable and a

DVI-D cable.

• For easier cable routing, the power and Garmin Marine

Network cables are packaged without the locking rings

installed. The cables should be routed before the locking

rings are installed.

• After installing a locking ring on a cable, you should make

sure the ring is securely connected and the o-ring is in place

so the power or data connection remains secure.

Connecting to Power

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

Route the power cable to the power source and to the

device.

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

Install the locking ring and o-ring on the end of the power

cable.

Connect the power cable to the device by turning the locking

ring clockwise.

Additional Grounding Considerations

This device should not need any additional chassis grounding in

most installation situations. If interference is experienced, the

grounding screw on the housing can be used to connect the

device to the water ground of the boat to help avoid the

interference.

Power Cable Extensions

If necessary, the power cable can be extended using the

appropriate wire gauge for the length of the extension.

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Garmin GMM 150 Marine Monitor Manual de instalación Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para No Garmin GMM 150 Marine Monitor