Garmin GHP 10 System Manual de instalación descargar pdf (Pagina 10)

10 GHP 10 Installation Instructions



After you have completely planned the GHP 10 installation on your

boat, and have satised all the hydraulic, mounting, and connection

considerations for your particular installation, you can begin mounting

and connecting the components.



To install the Shadow Drive, connect it to the hydraulic steering line of

your boat and connect it to the CCU/ECU interconnect cable.



Before you can install the Shadow Drive, you must select a location at

which to connect the Shadow Drive to the hydraulic steering of your

boat, after you have read and followed the mounting and connection

considerations (page 5). For more information, consult the hydraulic-

layout diagrams found in the installation instructions included in the

pump box.

Use the included connectors to install the Shadow Drive in the

hydraulic line.



When connecting the Shadow Drive to the hydraulic system, follow the

important considerations (page 5).

To connect the Shadow Drive, connect it to the CCU/ECU interconnect

cable.

1. Route the bare-wire end of the CCU/ECU interconnect cable to the

Shadow Drive.

If the cable is not long enough, extend the appropriate wires with 28

AWG wire.

2. Connect the cables, based on the table below.

 



Red (+) Brown (+)

Black (-) Black (-)

3. Solder and cover all bare-wire connections.



To install the ECU, mount it to your boat (page 10), connect it to the

pump and to the CCU (page 11), and connect it to the boat battery

(page 10).



The ECU hardware has been updated to function with 24 Vdc electrical

systems, though older ECU units run on only 12 Vdc electrical systems.

To determine if your ECU is compatible with a 24 Vdc system, examine

the serial number on the ECU (page 5).

NOTE: The GHP 10 system software (CCU software) must be version

2.70 or newer in order to support 24 Vdc installations.



Before you can install the ECU, you must select a mounting location

and determine the correct mounting hardware (page 5).

1. Cut out the mounting template provided on page 23.

2. Tape the template to the mounting location.

3. Drill pilot holes at the four mounting locations.

4. Use screws to mount the ECU.



Notice

Do not remove the in-line fuse holder from the battery cable when

connecting to the battery. If you remove the in-line fuse holder, you will

void the GHP 10 warranty and possibly damage the GHP 10 autopilot

system.

You should connect the ECU power cable directly to the boat battery

if possible. Although it is not recommended, if you connect the power

cable to a terminal block or other source, connect it through a 40 A fuse.

If you plan to route the ECU through a breaker or a switch near the

helm, consider using an appropriately sized relay and control wire

instead of extending the ECU power cable.

1. Route the connector-terminated end of the ECU power cable to the

ECU, but do not connect it to the ECU.

2. Route the bare-wire end of the ECU power cable to the boat battery.

If the wire is not long enough, it can be extended.

3. Determine the correct wire gauge for an extended run, based on the

table below.

 

10 ft. (3 m) 12 AWG (3.31 mm

)

15 ft. (4.5 m) 10 AWG (5.26 mm

)

20 ft. (6 m) 10 AWG (5.26 mm

)

25 ft. (7.5 m) 8 AWG (8.36 mm

)

4. Connect the black wire (-) to the negative (-) terminal of the battery.

5. Connect the red wire (+) to the positive (+) terminal of the battery.

6. Do not connect the ECU power cable to the ECU.

Connect the power cable to the ECU only after you install all of

the other GHP 10 components.



To install the CCU, you must mount it to your boat (page 10), connect

it to the ECU (page 11), connect it to a NMEA 2000 network (page 12),

and connect it to the alarm (page 11) and to the yellow CCU signal wire

on the GHC 20 (page 11).



Before you can mount the CCU, you must select a location and

determine the correct mounting hardware (page 5).

The CCU bracket has two portions, the mounting portion and the

securing portion.

1. Cut out the mounting template provided on page 23.

2. Tape the template to the mounting location.

If you are installing the CCU on a vertical surface, install the

mounting portion of the bracket with an opening

➊

at the bottom.

➊

➋

3. Drill pilot holes at the three mounting locations.

4. Use screws

➋

to secure the mounting portion of the CCU bracket.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 25 26

Comentarios a estos manuales

Sin comentarios

Garmin GHP 10 System Manual de instalación Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para No Garmin GHP 10 System