Garmin Software Version 0321.23 Manual Pagina 117
- Pagina / 266
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
G1000 System Maintenance Manual – Diamond DA40/40F Page 4-25
190-00545-01 Revision G
4.10.2.1 Pitch Servo Slip Clutch Torque Check
1. Press the small FMS knob to activate the cursor. Rotate the large FMS knob to highlight the
SELECT SERVO AXIS field. Rotate the small FMS knob to display the drop down menu then rotate
the small FMS knob to select the PITCH SERVO and press ENT.
2. Verify that the PFT status fields show PASSED.
IMPORTANT!
If the test must be stopped, firmly grasp the aircraft control being moved and press
the red AP DISC switch on the aircraft control stick. If an abnormal disconnect of a
servo occurs, reset AFCS circuit breaker and repeat the step.
3. Verify that the aircraft control surface to be checked is free to travel throughout its range of motion.
4. Position the control surface in the neutral position.
5. Press the TEST SVO softkey. Use the large FMS knob to highlight YES and press the ENT key.
6. Verify the MFD shows a white CAS message CLUTCH PIT PROG, which indicates that the test of
the stated axis is in progress.
7. Verify the PITCH SERVO drives the control surface to the NOSE UP stop.
8. After approximately a 25 second data collection period has expired, verify the servo automatically
drives in the opposite direction and begins data collections for the NOSE DOWN stop.
9. Allow the PITCH SERVO to drive the control surface to the NOSE DOWN stop.
10. After approximately a 25 second data collection period has expired, verify the MFD shows the
CLUTCH PIT PASS message.
11. Press the ENT key to acknowledge the COMPLETE prompt on the PFD.
12. If the MFD shows the CLUTCH PIT FAIL message repeat the test twice in the failed axis. If the test
does not pass, the GSM 86 slip clutch cartridge must be replaced or tested using the Manual Slip
Clutch Test Procedure, Section 4.10.3.
IMPORTANT!
The Min and Max Torque values displayed on the MFD should not be used to
determine whether the test passed or failed. Only the presence of the CAS message
CLUTCH PIT PASS on the MFD can make sure that the test passed in a given axis.
NOTE
The CAS messages for CLUTCH PIT PASS or CLUTCH PIT FAIL will remain in
the CAS window until aircraft power is removed. On the next aircraft power up the
messages will be removed.
13. Firmly grasp the control stick and press the red AP DISC button on the control stick to relieve any
control tension.
- Diamond DA 40 & DA 40 F 1
- PARAGRAPH PAGE 4
- FIGURE PAGE 6
- TABLE PAGE 9
- 1 INTRODUCTION 11
- 1.2 Organization 19
- 1.3.1 Units of Measure 21
- 1.4 Publications 22
- 1.5 Distribution 24
- (Where Applicable) 25
- 2 SYSTEM DESCRIPTION 27
- 2.2 Equipment Descriptions 28
- 2.2.2 GMA 1347 Audio Panel 28
- 2.3.1 KAP 140 AFCS 31
- • Flight Director 34
- • Autopilot 34
- • Manual Electric Trim 34
- • Pitch 37
- • Pitch Trim 37
- • Roll 37
- 2.8 Shield Block Grounds 43
- 2.9 Sensor Installations 43
- 2.10 Block Diagrams 43
- 2.10.1 G1000 & KAP140 43
- 2.10.2 G1000 & GFC700 44
- 3.1.1 AFCS Controls 45
- 3.1.2 GMA 1347 Controls 46
- 3.1.3 FMS Knob 46
- 3.1.4 Softkeys 47
- 3.2 G1000 Operation Modes 47
- 3.2.1 Normal Mode 47
- 3.2.2 Reversionary Mode 48
- Configuration Mismatch 51
- SET>ACTV Softkey 51
- Configuration Correct 51
- 3.3.2 Configuration Prompts 52
- 3.4.2 Software Files 59
- 3.4.3 Configuration Files 60
- GRS Internal Memory 66
- GDC Internal Memory 66
- GDU 104X Software Load 67
- G1000 System Upload Selection 67
- 3.5.1 System Power Up 68
- 3.5.8 Software Check 77
- 3.5.9 TAWS Reactivation 80
- 3.5.11 ESP Reactivation 82
- SYSTEM ID Number Location 85
- 4.2 Servicing Information 94
- 4.2.2 Recommended Tools 95
- 4.3 Maintenance Intervals 96
- G1000 Equipment 96
- 4.4 Visual Inspection 100
- 190-00545-01 Revision G 101
- 4.5 Electrical Bonding Test 103
- 4.5.1 Requirements 103
- 4.5.2 Test Equipment 103
- 4.5.3 Procedure 103
- 4.6.2 Calibration Setup 108
- 4.6.3 Empty Calibration 109
- 4.6.4 5 Gallon Calibration 111
- message 118
- Figure 4-14) 124
- Figure 4-15) 125
- Revision G 190-00545-01 128
- INLET AND 129
- DUCT (REF) 129
- 5 TROUBLESHOOTING 133
- Annunciation Window 134
- Alerts Window 134
- Alerts Softkey Annunciation 134
- System Annunciations 134
- Alert Name Purpose 136
- 5.2 System Annunciations 137
- Calibration): 139
- 5.2.3 ADF/DME Failure 143
- *KAP140 aircraft only 144
- Message Advisory Solution 145
- 5.4 TAWS Troubleshooting 146
- Condition Resolution 149
- 5.5.2 GFC Status Page 150
- SERVO DATA 151
- SLIP CLUTCH TEST RESULTS 151
- 5.5.5.1 Monitor Processor 156
- 5.5.5.2 Control Processor 157
- 5.6.1 Overview 159
- Primary Data Path 160
- Secondary Data Path 160
- Third Data Path 162
- Fourth Data Path 162
- Channel LRU Indicator Status 165
- 5.8 GDU 104X Alerts 175
- 5.8.2 Database Alerts 176
- 5.8.3 Cooling Alerts 177
- 5.8.4 Datacard Alerts 178
- 5.8.5 Key Alerts 178
- 5.8.6 Miscellaneous Alerts 179
- 5.8.7 GMA Common Problems 181
- 5.8.8 GMA Alerts 181
- 5.9 GIA 63 Troubleshooting 182
- 5.9.1 COM 182
- 5.9.2 NAV 182
- 5.9.3 G/S 182
- 5.9.4 GPS 182
- 5.10 GIA Alert Messages 183
- 5.10.1 COM Alerts 183
- 5.10.2 NAV Alerts 184
- 5.10.3 Glideslope Alerts 185
- 5.10.4 GPS Alerts 185
- 5.10.5 GIA Cooling Alerts 186
- 5.11 GEA Troubleshooting 187
- 5.11.1 GEA Common Problems 187
- 5.11.2 GEA Alerts 187
- 5.12 GTX Troubleshooting 187
- 5.12.1 GTX Alerts 187
- 5.13.1 AHRS Common Problems 188
- 5.13.2 GRS Alerts 188
- 5.13.3 GMU Alerts 189
- 5.14.2 GDC Alerts 189
- 5.15.2 GDL 69A Alerts 191
- 5.16 GDL 59 Troubleshooting 191
- 5.16.1 GDL 59 Alerts 191
- 5.17 GSR 56 Troubleshooting 192
- 5.17.1 GSR 56 Alerts 192
- Symptom Recommended Action 193
- Table 5-58 193
- 5.19 ESP Troubleshooting 194
- ___________ 196
- 6.1 GDU 104X MFD & PFD 198
- 6.2 GMA 1347 Audio Panel 198
- 6.5 GTX 33 Transponder 199
- 6.6 GTP 59 OAT Probe 200
- 6.7 GRS 77 AHRS 200
- 6.8 GMU 44 Magnetometer 201
- 6.9 GDL 69A 201
- Replacement: 202
- 3 Screw 1 211-60234-08 205
- 6.14 GA35 GPS/WAAS Antennas 206
- 7.1 GDU 104X MFD & PFD 211
- 7.1.2 GDU Software Loading 213
- 7.1.3 PFD/MFD Testing 213
- 7.2 GMA 1347 Audio Panel 215
- 7.2.2 GMA 1347 Testing 216
- 7.3.2 GIA 63 Testing 220
- • 131.250 MHz 221
- • 131.275 MHz 221
- • 131.300 MHz 221
- • 121.175 MHz 221
- • 121.200 MHz 221
- • 121.190 MHz 222
- • 130.285 MHz 222
- • 131.290 Mhz 222
- 7.4.2 GEA 71 Testing 225
- 7.5 GTX 33 Transponder 227
- 7.5.3 GTX 33 Testing 228
- 7.6.2 GDC 74A Testing 230
- 7.6.3 Airspeed Test 231
- 7.6.5 OAT Probe Check 232
- Procedure B: 234
- ROVIDED) 235
- 7.7.3 GRS/GMU Testing 243
- 7.8 GDL 69 XM Data Link 244
- 7.8.2 GDL 69 Testing 245
- 7.9 GDL 59 Datalink 245
- 7.9.2 GDL 59 Test 246
- 7.10 GSR 56 247
- 7.10.1 GSR 56 Testing 248
- GSR 56 Standalone Option 249
- GSA 81 Servo 250
- 7.11.2 GSA 81 Testing 251
- 8.1 Software Verification 253
- 8.2.1 GPS Failure Test 255
- 8.2.2 GIA Failure Test 256
- 8.2.3 Display Failure Test 258
- 8.3 GFC 700 Ground Checkout 262
- 8.3.1 Pre-Flight Test 262
- 8.3.2 AFCS Switch Checks 263
- 8.4 Maintenance Records 265
Relacionado con productos y manuales para Navegadores Garmin Software Version 0321.23
Navegadores Garmin GPS 12CX Manual de usuario
(67 paginas)
(67 paginas)
Navegadores Garmin GPSMAP 496 Manual de usuario
(196 paginas)
(196 paginas)
Navegadores Garmin Pilatus PC_6 Guía de usuario
(404 paginas)
(404 paginas)
Navegadores Garmin GPS Kit Manual de usuario
(54 paginas)
(54 paginas)
Navegadores Garmin Appliance Data Guía de usuario
(148 paginas)
(148 paginas)
Navegadores Garmin Part 23 AML STC Manual de usuario
(40 paginas)
(40 paginas)
Navegadores Garmin GMR 18/24 Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 1.632 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales