Garmin Software Version 0321.23 Manual Pagina 230
- Pagina / 266
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Page 7-22 G1000 System Maintenance Manual – Diamond DA40/40F
Revision G 190-00545-01
12. After the software and configuration files are loaded, turn off the system and remove the G1000
system software loader card. Reinsert the supplemental database cards in the bottom slot of each
display. Be sure to insert the card removed from the MFD back into the MFD.
13. Continue to the GDC 74A Testing section.
7.6.2 GDC 74A Testing
Apply power to the G1000 and allow system to initialize.
IMPORTANT!
Allow unit to warm up for 15 minutes before performing the following tests.
On the PFD, open the ALERT window and verify there are no GDC MANIFEST or configuration error
messages.
Verification of the altimeter and airspeed must be performed using a pitot/static ramp tester. The static
port and altimeter must be verified in accordance with Title 14 of the Code of Federal Regulations (CFR)
§ 91.411 and Part 43 Appendix E, every 24 calendar months.
For system software 0321.17 or later, the G1000 pitot/static system may be tested in normal display
mode.
To properly conduct these tests on G1000 systems equipped with System Software Version 0369.13 or
earlier, perform the following procedure:
To prepare the G1000 System for Part 43 Appendix E testing (0369.13 or earlier only):
1. Remove power to the PFD by pulling the circuit breaker labeled PFD.
2. Press and hold the ENT key on the PFD while applying power using the PFD circuit breaker.
3. Release the ENT key after ‘INITIALIZING SYSTEM’ appears in the upper left corner of the
PFD.
4. Rotate the FMS knob to until the display shows the GRS page group. Within the Air Data 1 sub
window is the field “B ALT” which is Barometric Altitude. B ALT is equivalent to the altitude
that will be displayed to the pilot on the altitude display when the PFD is in normal mode. B ALT
will be used for all CFR Part 43 Appendix E tests for G1000 altitude.
5. Push the red “display backup” button on the audio panel. This will activate Reversionary Mode
for the MFD. Baro settings can then be read from the MFD for the CFR Part 43 Appendix E tests.
6. After completing the tests specified by § 91.411 and Part 43 Appendix E, return the MFD to
normal mode by pushing the red “display backup” button. Return the PFD to normal mode by
pulling the PFD circuit breaker and then resetting.
NOTE
The following tests are above and beyond the requirements set forth in Appendix E.
- Diamond DA 40 & DA 40 F 1
- PARAGRAPH PAGE 4
- FIGURE PAGE 6
- TABLE PAGE 9
- 1 INTRODUCTION 11
- 1.2 Organization 19
- 1.3.1 Units of Measure 21
- 1.4 Publications 22
- 1.5 Distribution 24
- (Where Applicable) 25
- 2 SYSTEM DESCRIPTION 27
- 2.2 Equipment Descriptions 28
- 2.2.2 GMA 1347 Audio Panel 28
- 2.3.1 KAP 140 AFCS 31
- • Flight Director 34
- • Autopilot 34
- • Manual Electric Trim 34
- • Pitch 37
- • Pitch Trim 37
- • Roll 37
- 2.8 Shield Block Grounds 43
- 2.9 Sensor Installations 43
- 2.10 Block Diagrams 43
- 2.10.1 G1000 & KAP140 43
- 2.10.2 G1000 & GFC700 44
- 3.1.1 AFCS Controls 45
- 3.1.2 GMA 1347 Controls 46
- 3.1.3 FMS Knob 46
- 3.1.4 Softkeys 47
- 3.2 G1000 Operation Modes 47
- 3.2.1 Normal Mode 47
- 3.2.2 Reversionary Mode 48
- Configuration Mismatch 51
- SET>ACTV Softkey 51
- Configuration Correct 51
- 3.3.2 Configuration Prompts 52
- 3.4.2 Software Files 59
- 3.4.3 Configuration Files 60
- GRS Internal Memory 66
- GDC Internal Memory 66
- GDU 104X Software Load 67
- G1000 System Upload Selection 67
- 3.5.1 System Power Up 68
- 3.5.8 Software Check 77
- 3.5.9 TAWS Reactivation 80
- 3.5.11 ESP Reactivation 82
- SYSTEM ID Number Location 85
- 4.2 Servicing Information 94
- 4.2.2 Recommended Tools 95
- 4.3 Maintenance Intervals 96
- G1000 Equipment 96
- 4.4 Visual Inspection 100
- 190-00545-01 Revision G 101
- 4.5 Electrical Bonding Test 103
- 4.5.1 Requirements 103
- 4.5.2 Test Equipment 103
- 4.5.3 Procedure 103
- 4.6.2 Calibration Setup 108
- 4.6.3 Empty Calibration 109
- 4.6.4 5 Gallon Calibration 111
- message 118
- Figure 4-14) 124
- Figure 4-15) 125
- Revision G 190-00545-01 128
- INLET AND 129
- DUCT (REF) 129
- 5 TROUBLESHOOTING 133
- Annunciation Window 134
- Alerts Window 134
- Alerts Softkey Annunciation 134
- System Annunciations 134
- Alert Name Purpose 136
- 5.2 System Annunciations 137
- Calibration): 139
- 5.2.3 ADF/DME Failure 143
- *KAP140 aircraft only 144
- Message Advisory Solution 145
- 5.4 TAWS Troubleshooting 146
- Condition Resolution 149
- 5.5.2 GFC Status Page 150
- SERVO DATA 151
- SLIP CLUTCH TEST RESULTS 151
- 5.5.5.1 Monitor Processor 156
- 5.5.5.2 Control Processor 157
- 5.6.1 Overview 159
- Primary Data Path 160
- Secondary Data Path 160
- Third Data Path 162
- Fourth Data Path 162
- Channel LRU Indicator Status 165
- 5.8 GDU 104X Alerts 175
- 5.8.2 Database Alerts 176
- 5.8.3 Cooling Alerts 177
- 5.8.4 Datacard Alerts 178
- 5.8.5 Key Alerts 178
- 5.8.6 Miscellaneous Alerts 179
- 5.8.7 GMA Common Problems 181
- 5.8.8 GMA Alerts 181
- 5.9 GIA 63 Troubleshooting 182
- 5.9.1 COM 182
- 5.9.2 NAV 182
- 5.9.3 G/S 182
- 5.9.4 GPS 182
- 5.10 GIA Alert Messages 183
- 5.10.1 COM Alerts 183
- 5.10.2 NAV Alerts 184
- 5.10.3 Glideslope Alerts 185
- 5.10.4 GPS Alerts 185
- 5.10.5 GIA Cooling Alerts 186
- 5.11 GEA Troubleshooting 187
- 5.11.1 GEA Common Problems 187
- 5.11.2 GEA Alerts 187
- 5.12 GTX Troubleshooting 187
- 5.12.1 GTX Alerts 187
- 5.13.1 AHRS Common Problems 188
- 5.13.2 GRS Alerts 188
- 5.13.3 GMU Alerts 189
- 5.14.2 GDC Alerts 189
- 5.15.2 GDL 69A Alerts 191
- 5.16 GDL 59 Troubleshooting 191
- 5.16.1 GDL 59 Alerts 191
- 5.17 GSR 56 Troubleshooting 192
- 5.17.1 GSR 56 Alerts 192
- Symptom Recommended Action 193
- Table 5-58 193
- 5.19 ESP Troubleshooting 194
- ___________ 196
- 6.1 GDU 104X MFD & PFD 198
- 6.2 GMA 1347 Audio Panel 198
- 6.5 GTX 33 Transponder 199
- 6.6 GTP 59 OAT Probe 200
- 6.7 GRS 77 AHRS 200
- 6.8 GMU 44 Magnetometer 201
- 6.9 GDL 69A 201
- Replacement: 202
- 3 Screw 1 211-60234-08 205
- 6.14 GA35 GPS/WAAS Antennas 206
- 7.1 GDU 104X MFD & PFD 211
- 7.1.2 GDU Software Loading 213
- 7.1.3 PFD/MFD Testing 213
- 7.2 GMA 1347 Audio Panel 215
- 7.2.2 GMA 1347 Testing 216
- 7.3.2 GIA 63 Testing 220
- • 131.250 MHz 221
- • 131.275 MHz 221
- • 131.300 MHz 221
- • 121.175 MHz 221
- • 121.200 MHz 221
- • 121.190 MHz 222
- • 130.285 MHz 222
- • 131.290 Mhz 222
- 7.4.2 GEA 71 Testing 225
- 7.5 GTX 33 Transponder 227
- 7.5.3 GTX 33 Testing 228
- 7.6.2 GDC 74A Testing 230
- 7.6.3 Airspeed Test 231
- 7.6.5 OAT Probe Check 232
- Procedure B: 234
- ROVIDED) 235
- 7.7.3 GRS/GMU Testing 243
- 7.8 GDL 69 XM Data Link 244
- 7.8.2 GDL 69 Testing 245
- 7.9 GDL 59 Datalink 245
- 7.9.2 GDL 59 Test 246
- 7.10 GSR 56 247
- 7.10.1 GSR 56 Testing 248
- GSR 56 Standalone Option 249
- GSA 81 Servo 250
- 7.11.2 GSA 81 Testing 251
- 8.1 Software Verification 253
- 8.2.1 GPS Failure Test 255
- 8.2.2 GIA Failure Test 256
- 8.2.3 Display Failure Test 258
- 8.3 GFC 700 Ground Checkout 262
- 8.3.1 Pre-Flight Test 262
- 8.3.2 AFCS Switch Checks 263
- 8.4 Maintenance Records 265
Relacionado con productos y manuales para Navegadores Garmin Software Version 0321.23
Navegadores Garmin GPS 12CX Manual de usuario
(67 paginas)
(67 paginas)
Navegadores Garmin GPSMAP 496 Manual de usuario
(196 paginas)
(196 paginas)
Navegadores Garmin Pilatus PC_6 Guía de usuario
(404 paginas)
(404 paginas)
Navegadores Garmin GPS Kit Manual de usuario
(54 paginas)
(54 paginas)
Navegadores Garmin Appliance Data Guía de usuario
(148 paginas)
(148 paginas)
Navegadores Garmin Part 23 AML STC Manual de usuario
(40 paginas)
(40 paginas)
Navegadores Garmin GMR 18/24 Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.098 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales